what should i do? no one seems to be responding to this issue? do i need to restore back to 1.1.1 and rejailbreak?

not sure if i still have the 1.1.1 file, does anyoen know where i can download the file?

can i rejailbreak via jailbreak.com or whatever that initial site was?

any help would be great.

If you didn’t install OktoPrep, you might have to start from scratch. Before updating 1.1.2, you should unlock your phone using one of the various methods.

Or, you could go and download ziphone which does all of this for you.

Only thing I’ve noticed lately is the installation of new programs do not work very much any more. Not sure if that’s because I used this method.

Thanks

If you use this method, you will find that some applications you install will not appear on the Springboard. You’ll also encounter the Install script error when installing certain applications (weDict for example).

Instead, I recommend this method:

1. Downgrade to 1.1.1 firmware
2. Go to http://www.jailbreakme.com and install the AppSnapp at the bottom.
3. Go to the installer and install the Community Sources (located under the “Sources” category).
4. Next, go to the “Tweaks 1.1.1″ section and install “OktoPrep.” Press the Home button once you’re done so Springboard will reload.

Update to 1.1.2 firmware using iTunes
Install the 1.1.2 jailbreak from dev team.

If you are unsure of how to do the above 1.1.1 and 1.1.2 jailbreak steps, check out this guide by CrunchGear: http://www.crunchgear.com/2007/11/19/help-key-how-to-jailbreak-your-ipod-touch-with-112/

Once your iPod Touch is on 1.1.2 jailbreak, go to the installer and check the Sources again. If you see the Community Sources there, install it. Next, install the BSD Subsystem (under “System”) and the BSD Subsystem fix (under “Tweaks”, this is optional)

Then go to “All packages” and look for “Official 1.1.3 Updater” (version 3) from dev team. This will take a lot longer than the method described in the article; however, the compatibility will be much better.

Good luck!

now i have to re-download the whole thing again

I have a 1.1.2 jailbroken iphone using stealthsim with a UK sim card (not o2) in it. Am I able to upgrade to 1.1.3 without locking the phone and still be able to use the stealthsim ok?

Help, please…….

I found the an article at the line below which gave these instructions:

If you’re a Windows user…
1. You must be on a PC connected to the same wireless network as your iPhone. Download these files and save them to your Desktop:
* PCSP for Windows (by the maker of PuTTY)
* PuTTY for Windows (SSH Client)
Now open a command window by going to your Start menu, clicking Run, and typing in ‘cmd’. Type the following commands:
1.) “cd desktop”
2.) “putty -ssh root@” with same replacement and password as above. When it asks for a password, type in “alpine” and press Enter (nothing will appear as your type in the password - this is normal).

I did this through the CMD window via PUTTY and it actually shutdown my iTOUCH and caused me to lose the connection as well. When it rebooted - to my surprise all of the new apps were installed. Now…I tried this directly in the iTOUCH as well as instructed in this post at the very top. It wouldn’t accept “alpine”. But when I did it through the putty session it worked.

Here is the post I found that may help. I didn’t perform the full jailbreak from PCSP as mentioned in the post at the link below. Up until the password issue I had followed the step by step instructions in this article above.

http://forums.macrumors.com/showthread.php?t=422278&highlight=jailbreak+password#Upgrading_and_jailbreaking_your_iPhone_in_1.1.3

Hope that helps.

So, i rebooted and then it just says last login

Hasn’t done anything in the past 15 mins…. I know it says it can take up to 45 mins to finish…. has it crashed/locked or is it suppose to do that???